Select Page

FAX:  (314) 436-0481

Description

400-latches

General Fasteners Guide

Tensil Strength
ULTIMATE TENSILE STRENGTH
The ultimate tensile strength (UTS) for our items is shown in the relevant product tables throughout the catalogue. The figures for the UTS have been determined by tensile tests in a normal working load direction on standard products and do not include any safety factors. A maximum load rate of 30mm per minute was applied throughout the tests. The UTS figures are shown in kilograms and for a Safe Working Load we suggest that approximately half of the ultimate strength figure is used.

Rigid Claw Fastener
RIGID CLAW FASTENERS

Rigid claw fasteners are manufactured from rigid steel strip or rigid wire forms. Where rigid claw fasteners are fitted we suggest that a rubber type seal is used within the application to provide some resilience between the fastener and catch plate.

If this is not possible we suggest that a spring claw fastener should be used.

Compression Spring Loaded
SPRING CLAW FASTENERS

Spring claw fasteners are manufactured using spring steel curved wire or coil springs and can be used to provide resilience. The degree of spring deflection up to a maximum working load varies between different fasteners and is shown in the relevant product tables within the catalogue.

Extension spring claws pulled beyond their maximum working load will take a permanent set. Compression spring claws pulled beyond their maximum working load will become coil bound (i.e. rigid) and will no longer act as a spring.

Adjustable Fastener
ADJUSTABLE FASTENERS

Adjustable fasteners incorporate either a screwed spindle or threaded eyebolt and trunnion which produce a minimum 10mm of adjustment. This gives the strength advantages of a rigid fastener while allowing the required tension to be set after fitting.

Catch Plate
CATCH PLATES

The alternative catch plates which are recommended for each fastener are shown in the relevant product tablesthroughout the catalogue. These may included flat, wide, narrow, 90o crank, reverse crank, joggled and no holes self finish suitable for welding.
Catch Plate Types

Fastener Materials
MATERIAL & FINISH

Our products are usually offered in mild steel (MS) zinc plated or stainless steel (SS).
The standard zinc plated finish for each fastener is either silver passivate (ZN) or yellow colour passivate (ZN/YP) and is shown in the product tables.

Certain fasteners and catchplates are available in mild steel self finish (SF) with
no holes (NH) for welding. Some of the 40- series have self finish bases (SFB) for welding with the remaining parts of the fastener zinc plated.

Zinc plate does provide some corrosion resistance for mild steel but when fitting fasteners outside, stainless steel will offer greater corrosion resistance.

We generally manufacture our products from type 304 stainless steel. However, some fasteners and catch plates are available in type 316 as standard, and some as an option. These are shown in the product tablesas SS316 where available.

Some products are also available in mild steel with a black electrophoretic paint (BL) as standard. These are also shown in the product tables.

Safety Catch
SAFETY CATCH

To prevent accidental release, certain fasteners are offered with a top mounted or a patented side action safety catch. Please look for the triangle symbol in the product tables.

Optional Sealing Pins
SEALING FACILITY

Many fasteners are available with sealing holes, shown as the pin symbol in the product tables, which allows for a sealing pin or wire to be used. We can supply two different styles of sealing pin.

Fastener Dimension Guide
DIMENSIONS

This catalogue shows the length dimension A, width dimension B and height dimension C in millimetres for each standard product.

Our 71-2600SS has an internal coil spring for continuous clamping under vibration loads. This is also fitted with safety catch to prevent accidental opening. This latch is stronger and has a more robust construction when compared to the 36-1163SS . An image of this latch below.

 

Get in touch with HardwareMFG.com 

 

Proud Member of:

Hardware MFG
1415 S. 18th
Saint Louis, MO 63104
HardwareMFG@aol.com
Phone: (314) 436-0432
Fax: (314) 436-0481

 

Copyright 2019 Hardware MFG. All rights reserved